Dinas Silica Mine.

Derelict Places

Help Support Derelict Places:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

Engineer

Veteran Member
Veteran Member
Joined
Jun 14, 2008
Messages
474
Reaction score
63
Location
Wales.
Had a quick outing to this mine to try some pics with an Oldham LED conversion.

Lower Workings.
IMG_2658.png


Lowest level above water table.

IMG_2662.png


IMG_2663.png


General shot of haulage level, bit too much exposure!

IMG_2666.png
 
Wonderful, that Oldham lamp really cuts through the darkness!

Thanks,:) some old pics here, combination of carbide, standard Oldham and 250,000 CP handlamp.

[ame]http://www.derelictplaces.co.uk/main/showthread.php?t=5689[/ame]
 
Some good pictures there Engineer, been in there a few time myself to play with the camera. The light looks good to, any possibility of a picture of it from the front.
 
any possibility of a picture of it from the front.

It's been tidied up a bit since the pic.

IMG_2683.png


The base unit is a Cree R2 unit reputed to be 300 lumen.

797.png


The Oldham reflector has been discarded and a heat sink assembly made up to dissipate the extra heat.

Mods1.png


Finally the contacts have been modified to connect with slip rings on the rear of the heat sink.

IMG_2679.png

IMG_2678.png


Edit: the pics with this lamp were 15 sec @ f2.8 with the light stationary.
 
Last edited:
Thanks for that Engineer, that’s very good when I have done Oldham conversions I have taken the guts out and fitted a heat sink inside the light, will have to see if I can do something along the lines of what you have.
 
I originally copied the rough design from a similar set up seen on another forum with some of my own modifications.
 
I am currently using a three mode driver pcb, and a cree xlamp led running at 228lm on full power which is 1 amp and 14 small led’s (3mm) all inside the head set around a heatsink.
 
I am currently using a three mode driver pcb, and a cree xlamp led running at 228lm on full power which is 1 amp and 14 small led’s (3mm) all inside the head set around a heatsink.

That sounds a nice set-up, got a pic?
 
Here you go one picture, got the bits from Dealextreme or most of it LED about £4.75 and driver PCB about £3 and got the lens & diffuser from Farnell about £2.30, and have loads of the small 3mm LEDs. The rest is just wire glue and a piece of aluminium for a heat sink.

DSCF1184-1.jpg
 
Thanks, looks a handy bit of kit and a very neat conversion. Some sample pics of the old bulb set up and the LED conversion, camera settings identical.

1 amp bulb
OldhamBulb.png


LED conversion.
OldhamLED.png
 
like the mine,is it the one with flooded sections that cave divers use or am i on the wrong mine,also you have the same chip as me in your headlamp,are you running them on 18650s or standard pack
 
like the mine,is it the one with flooded sections that cave divers use or am i on the wrong mine,also you have the same chip as me in your headlamp,are you running them on 18650s or standard pack

Yep, that's the one the divers use but the lower workings pic is at the bottom of the tunnel which is opposite the main mine.

I'm still on the Oldham T3 battery for as long as it lasts.:)
 
The light is just so much more with the LED’s, I am more used to making up lights for off road mounting biking at night, have just started on the caving/mine lights and what limits me at the moment is the heat sinking for the LED’s I am now looking at getting one of these:

http://ledsupply.com/creexpg-w417.php
 
Yep, that's the one the divers use but the lower workings pic is at the bottom of the tunnel which is opposite the main mine.

I'm still on the Oldham T3 battery for as long as it lasts.:)

thought it was but the pics had me confused for a min,nice pics mate,when it packs up try 18650s x 4 Protected as they last ages and are dam site lighter,love my oldham could not get rid of it.
nice job on the conversion a dam site neater than the one ive done
 
Yes on the same sit, but the narrow one they do is 16 degrees, so don’t know how good that would that would be under ground, but that would be ok for a wide angle bike light.

http://ledsupply.com/carclo-optics-xpg-3up.php

(We may get in trouble here for going off topic a bit and rambling on)

Handy site, thanks. Perhaps we should move to the equipment thread.
 

Latest posts

Back
Top