Pyestock Cell 3 2006-7

Derelict Places

Help Support Derelict Places:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

Simon

Well-known member
Joined
Sep 21, 2005
Messages
314
Reaction score
155
Location
Cambridge
I'm still working on my Pyestock site...

And next to be completed is Cell 3. I suspect the trench and parts of the underground sections (where you can walk under the cell itself) have now flooded - we had to wade through parts in 2006 and 2007.

c3m1.jpg

Cell 3 (630)

Built: 1961
Decommissioned: 2002

Cell 3 was the first testing cell built after plans in the early 1950s to expand the initial capacity of the site. Constructed at the same time as the Air House, it was designed as a general purpose cell to provide greater capacity than Cell 2 e.g. it could cater for the new larger engines with their improved performance, and could simulate higher altitudes, all within a wider range of engine entry temperatures.

The cell was 138 feet long. The working section, where the gas turbine under test was connected, was 56 feet long, the diffusing section (where hot exhaust gases were rapidly cooled) was 64 foot long, the cooler and frame trap sections were 90 foot long with the rest of the length comprising the connection to the suction mains manifold. The diameters of these components was also impressive with the working section having a diameter of 20 foot, with a removable section in the roof, and the diameters of the diffuser and cooler sections were 10 foot and 30 foot respectively.

Such a structure should've had a major presence, easily dwarfing the size of Cells 1 and 2 which it replaced. But to reduce unwanted emitted noise, the whole structure was submerged below ground level in a concrete trench. Therefore there was little outward appearance of this complicated engineering installation.

3.jpg

Two buildings were constructed on top of this trench. The first was the main cell building which covered the working section. This steel framed building was typical of the austere, functional buildings of Pyestock. It was shuttered at its western end to allow gas turbines to be winched into the loading bay and then lowered in a well which contained the working section. The northern side was clad with glass to increase the natural lighting, whilst brick appendages on the north and south sides provided space for workshops, storage space and control rooms for icing tests.

A second building was constructed over another well which gave access to the exterior of the exhaust manifold. This was little more than a metal frame with steel cladding over its northern and southern sides.

The main control room for the cell was housed in the Computer Building over 700 meters away. A tunnel, called Monks Passage, was constructed to provide a connection path between the control room and its cell.

26.jpg

The cell was connected to the new air main and suction mains which were constructed along with the Air House. It used the Air House (and later the Parsons No. 9 and No. 10 exhausters) to produce altitude conditions (unlike Cells 1 and 2 which were driven by the ejectors). Compressed air was supplied by the Air House only, whilst exhausting conditions could be produced by all the plant.

It could simulate altitude conditions to 70,000 ft. at mach 2.2, with temperature ranging from -70 through to 250 degrees.

etf3-11.jpg

Temperature control was achieved by a separate heating plant (since removed), a separate cold air plant (produced by a pre-cooler and pressure dryer system housed in a neighbouring building) and ice making facilities (which could be found in the Cell 3 building). The four fuel systems connected to the cell could also be varied and set to different temperatures and pressures. Additionally the GEC sets could be configured to draw air through the Ceca Air Drying Plant so tests could be conducted with dry air.

65.jpg

Cell 3 became one of the most used cells of the site, its positioning within the air and suction mains allowing a plethora of different connection strategies and options. Initially designed for testing large diameter engines and combat jet testing, it was later used for military engine testing. It could also be used for steady state performance measurement, control system evaluation, altitude relighting, the limits of combustion stability, the evaluation of engine performance in severe icing conditions and the tolerance to distorted inlet flows.

It only closed in 2002 when it was determined obsolete after over forty years of service. But its working life wasn’t quite over and the working section was dressed up for the feature film Sahara where the cell doubled-up as part of a futuristic toxic waste disposal facility.

Some choice shots follow:

7.jpg

The western section of Cell 3 looking west from the covered section to the suction mains. The connecting building at the other end is Cell 3 West.

9.jpg

South-western corner of Cell 3 looking across the roof of building 627.

17.jpg

Looking east towards Cell 3 from the rising suction main of Cell 3 West.

20.jpg

The testing room of Cell 3 looking east.

29.jpg

View north-west across the Ice Plant Control Room.

33.jpg

Elevated view westerly across the whole of the external building of Cell 3.

41.jpg

First basement floor alongside the southern wall of the cell testing chamber. Looking east.

50.jpg

Elevated view across the working section and looking up to the roof of the cell.

56.jpg

The view east from the end of the exhaust gas cooler towards the flame traps and water cooled diffuser.

58.jpg

Elevated view south-west across the third well and the air inlet.

65.jpg

Piping and connections for the water cooled diffuser section. Looking west.

68.jpg

Looking west across the southern flank of the water cooled diffuser section.

72.jpg

Climbing over the exhaust gas cooler to the well in the covered section.

75.jpg

The northern side of the exhaust gas cooler looking east.

79.jpg

View up from the second basement floor up to the well in the covered section. Looking west.

81.jpg

Doorway through bulkhead on the second basement floor to the suction mains. Looking west.

82.jpg

Stairs up the gully connecting the final sections of Cell 3 and Cell 3 West to the suction mains. Looking west.

83.jpg

Elevated view east of the bulkhead door which leads to the second basement under Cell 3.​

There are more pictures and a full walkthrough on my website.

All the best,
Simon
 
Inspiring and fascinating stuff Simon!

This place was as the top of my "to do" list for such a long time after stumbling across your website some time ago. When I did finally get to visit it didn't disappoint and very much looking forward to going back again ... many more times ;)

Very interested in the details of the functions, workings and history of the various buildings so really enjoy reading all the additional info you provide. Also interesting to see how the place has changed over the years when comparing my own recent photographs of the place to your much earlier ones.

Many thanks and much respect for these additional "snippets" and the updates to the website and long may it continue! :)
 
Your work on pye is second to none.

You really know your stuff and what a fabulous site you have built up!

I got a serious soaking in the base of this bugger earlier this year.....

Excellent stuff! :)
 
Back
Top